1. Briefly talk about the difference between UV printing plate and ordinary printing plate and CTP printing plate.
UV ink suitability of various printing plates
Classification Common PS version UV ink PS version CTP Edition Brand VPS-A VPU LH-PI
The price is cheaper than the PS version of UV is more expensive than the ordinary PS version.
Since the actual sales price is decided by one agency, please contact the agency for details.
2. Is the printing plate easily dirty mainly due to several reasons?
(1) Cause: Underexposure, poor transparency of the Yang picture, and aging of the light source. Processing method: Reproduce the Yang picture and appropriately adjust the exposure time: Retry the test with the grey ladder ruler, extend the exposure time, or replace the light source lamp.
(2) Reason: The glass of the printing machine is a little dirty, and the adhesive residue is attached to the positive picture. Treatment method: Use glass cleaner and film cleaner to get dirty.
(3) Cause: During development, due to the adhesion of blisters, the development was poor, and the developing solution nozzle was bubbling due to clogging. Remedy: Eliminate blistering Cause: Clean the developing solution nozzles.
(4) Reason: When using the PS version, hands are not clean (there are fingerprint smears). Treatment method: Keep mouth and slightly after the operation.
(5) Reason: The glue is thin. Treatment method: Increase glue concentration.
(6) Cause: The adhesive layer was peeled off (when the adhesive layer was not dry, the adhesive was overlapped and stored). Treatment method: Do not keep in high temperature and high humidity conditions.
(7) Reason: After the plate is finished, it is stored under high temperature and high humidity conditions. Treatment method: Do not store under high temperature and high humidity conditions.
(8) Cause: The concentration of the developer was too low and the development was incomplete. Treatment method: adjust the developer to standard concentration.
3. How to improve the development quality of positive PS version?
The dilution rate of the developer should be respected by the proportion specified by the PS manufacturer, and a small sample plate (using the Fujifilm gray scale to expose a small-sized PS plate after exposure, which can measure the developer concentration). The developer concentration is managed.
4. In the printing process, the phenomenon of dirt on the printing plate is often seen. How can this be solved?
(1) Reason: When the printing stops, the printing plate is not wiped and protected. Treatment method: wipe protective plastic.
(2) Reason: The blank part of the printing plate is not wet enough. Treatment method: Increase the amount of water appropriately.
(3) Cause: Emulsification of the viscera occurred. Treatment method: Adjust the balance between ink and fountain solution, or replace the ink and fountain solution.
5. Why is it that film collages are prone to deficiencies?
(1) Reason: Improper film collage is not proper. Treatment method: The film from the image part 3 mm above the collage.
(2) Cause: The developer concentration is too high. Treatment method: adjust the developer to standard concentration.
1. Briefly talk about the difference between UV printing plate and ordinary printing plate and CTP printing plate.
UV ink adaptability classification of various printing plates Normal PS version UV ink PS version CTP version Brand VPS-A VPU LH-PI
The price is cheaper than the PS version of UV is more expensive than the ordinary PS version.
Since the actual sales price is decided by one agency, please contact the agency for details.
2. Is the printing plate easily dirty mainly due to several reasons?
(1) Cause: Underexposure, poor transparency of the Yang picture, and aging of the light source. Processing method: Reproduce the Yang picture and appropriately adjust the exposure time: Retry the test with the grey ladder ruler, extend the exposure time, or replace the light source lamp.
(2) Reason: The glass of the printing machine is a little dirty, and the adhesive residue is attached to the positive picture. Treatment method: Use glass cleaner and film cleaner to get dirty.
(3) Cause: During development, due to the adhesion of blisters, the development was poor, and the developing solution nozzle was bubbling due to clogging. Remedy: Eliminate blistering Cause: Clean the developing solution nozzles.
(4) Reason: When using the PS version, hands are not clean (there are fingerprint smears). Treatment method: Keep mouth and slightly after the operation.
(5) Reason: The glue is thin. Treatment method: Increase glue concentration.
(6) Cause: The adhesive layer was peeled off (when the adhesive layer was not dry, the adhesive was overlapped and stored). Treatment method: Do not keep in high temperature and high humidity conditions.
(7) Reason: After the plate is finished, it is stored under high temperature and high humidity conditions. Treatment method: Do not store under high temperature and high humidity conditions.
(8) Cause: The concentration of the developer was too low and the development was incomplete. Treatment method: adjust the developer to standard concentration.
3. How to improve the development quality of positive PS version?
The dilution rate of the developer should be respected by the proportion specified by the PS manufacturer, and a small sample plate (using the Fujifilm gray scale to expose a small-sized PS plate after exposure, which can measure the developer concentration). The developer concentration is managed.
4. In the printing process, the phenomenon of dirt on the printing plate is often seen. How can this be solved?
(1) Reason: When the printing stops, the printing plate is not wiped and protected. Treatment method: wipe protective plastic.
(2) Reason: The blank part of the printing plate is not wet enough. Treatment method: Increase the amount of water appropriately.
(3) Cause: Emulsification of the viscera occurred. Treatment method: Adjust the balance between ink and fountain solution, or replace the ink and fountain solution.
5. Why is it that film collages are prone to deficiencies?
(1) Reason: Improper film collage is not proper. Treatment method: The film from the image part 3 mm above the collage.
(2) Cause: The developer concentration is too high. Treatment method: adjust the developer to standard concentration.
The original brand-new door glass is damaged upon arrival and reissued free of charge. This is a white furnace door glass. It is simple and matched. In fact, it is super strong, not easy to break, and has a long life. The glass is made of Tempered Glass, which is heat-proof and explosion-proof. One-piece molding, multiple specifications, high projection light, no seams. Increase thicker. Microwave use, oven use. Beautiful and practical, you can see all kinds of delicacies in your noodles. And easy to clean, strong shock resistance, scratch resistance, wear resistance. Ignore the high temperature resistance, even if it is directly heated to high temperature, there is no need to worry about explosion. The glass adopts one-piece molding technology, no joints, and more beautiful and durable. Durable. We also have different specifications of tempered glass, support customization and processing, all at your service, we are a glass manufacturer, worthy of your trust.
We are China Oven Glass, Oven Glass Replacement manufacturer, choose the high quality Oven Door Glass Replace, Oven Door Glass Shattered, etc.
Oven Glass,Oven Glass Replacement,Oven Door Glass Replace,Oven Door Glass Shattered
WCH Temper Glass Co., Ltd , https://www.temperglasswch.com